Author Topic: How to Reset Windows Server 2008 Password  (Read 6190 times)

0 Members and 1 Guest are viewing this topic.

How to Reset Windows Server 2008 Password
« on: August 28, 2010, 12:59:51 AM »

Offline Nick

  • Administrator
  • Platinum Member
  • *
  • Posts: 46028
  • Karma: +1000/-0
  • Gender: Male
  • NickCS
    • http://www.facebook.com/nickcomputerservices
    • http://www.twitter.com/nickcomputer
    • Computer Chiangmai

You have just completed installing Windows Server 2008, and you hit the Ctrl+Alt+Delete key and then you were lost, What administrator password and username should I used? Especially that you did not create any during

 
 the installation process! In this article, I will show you how to successfully reset to Windows server 2008.

Windows Server 2008 is one of Microsoft Windows' server line of operating systems. Released to manufacturing on February 4, 2008, and officially released on February 27, 2008, it is the successor to Windows Server 2003, released nearly five years earlier. A second release, named Windows Server 2008 R2, was released to manufacturing on July 22, 2009.

The solution is a two stage process. The first stage is preparation and requires the use of PING (Partimage is not ghost) which is a linux environment that can run off of a disc. You need to download the PING image and burn it to a disc before continuing.

Now that you have the disc ready, here are the steps to follow:

1. Put the disc in your server and boot off of it. The process to do this differs by server but I am sure you can figure it out (or have done it before).

2. The PING linux environment will load.

3.When the environment is fully loaded, you will receive a ">>" prompt.

4.At the ">>" prompt, type "x" and press the ENTER key. "x" will take you to a command shell rather than launching the PING user interface.

6.At the "PING login:" prompt, type in "root" and press the ENTER key.

7.At this ping you should be logged into the PING operating system. Now we need to run a few shell commands.

Run the following command: fdisk -l : grep NTFS

8.This command will list all the NTFS partitions. As best as you can, note the name of the one that contains the Windows directory.

9.Run the following command: mkdir -p /mnt/windows

10.This command creates a directory called "/mnt/windows" that will be used for mounting the windows partition

11.Run the following command: mount -t ntfs-3g /dev/sda3 /mnt/windows


credit:  anny yu


 
Share this topic...
In a forum
(BBCode)
In a site/blog
(HTML)


Related Topics

  Subject / Started by Replies Last post
0 Replies
5178 Views
Last post July 02, 2010, 02:46:52 PM
by Nick
0 Replies
5582 Views
Last post July 02, 2010, 03:12:03 PM
by Nick
0 Replies
4501 Views
Last post July 02, 2010, 04:56:32 PM
by Nick
0 Replies
3843 Views
Last post July 03, 2010, 03:07:23 PM
by Nick
0 Replies
4957 Views
Last post July 03, 2010, 03:15:40 PM
by Nick
0 Replies
4161 Views
Last post July 03, 2010, 03:16:32 PM
by Nick
0 Replies
3575 Views
Last post July 03, 2010, 03:34:07 PM
by Nick
0 Replies
3189 Views
Last post July 03, 2010, 03:59:17 PM
by Nick
0 Replies
4302 Views
Last post December 02, 2010, 02:14:42 AM
by Nick
0 Replies
444 Views
Last post October 02, 2024, 12:28:56 PM
by siritidaporn